Whirlpool Washer Not Working/Repeating Cycle/Keeps Draining/Shuts Off [9 Easy Fixes]

Whirlpool is one of the largest home appliance manufacturers, with annual revenues of approximately $21 billion US. Even with such a large company, their appliances still have operational problems.

If your whirlpool washer not working, you’re probably frustrated and looking for an explanation. Uneven loads, hot water issues, and a stuck timer are some of the most common reasons why your Whirlpool washer isn’t working.

It could also be the result of a clogged drain or a blown fuse in your home. When it comes to large appliances like washers, hiring a professional is the best option.

If you want to know why your Whirlpool washer isn’t working, read the rest of this article. We will look at the most common problems that you may encounter with your washer, as well as how to fix them safely.

WHIRLPOOL WASHER KEEPS REPEATING CYCLE

It’s difficult enough to time your laundry cycles correctly when your machines are in good working order. When they act up and your cycles double or triple, your entire schedule can be thrown off.

The most common reason for your whirlpool washer to complete an entire wash cycle and then automatically restart is that it is stuck in a test mode.

Unplug the washer for ten seconds, then plug it back in and run the cleaning cycle to see if this is the problem. If the washing machine tries to repeat the cycle, it is most likely in “Continuous Test Mode,” which was addressed in a Technical Service Pointer distributed to Whirlpool technicians.

The directions for washers with individual status lights are as follows:

Make sure the washing machine is completely off. Using the main knob, make the following motions:

1. To reset the machine, turn the knob counterclockwise.
2. Wait.05 seconds after turning the knob clockwise until you hear a click.
3. Wait.05 seconds after turning the knob clockwise until you hear a click.
4. Wait.05 seconds after turning the knob clockwise until you hear a click.
5. Wait.05 seconds after turning the knob clockwise until you hear a click.
6. Wait until you hear one click after turning the main knob clockwise.

If this combination of movements does not resolve your repeating cycle issues, you should contact a technician from a local dealer.

WHIRLPOOL WASHER STUCK ON 1 MINUTE

Another common problem with Whirlpool washers is the never-ending one-minute timer. The machine may proceed normally through the entire wash cycle until the timer reaches one minute. The washer then spins for an extended period of time, sometimes up to an hour.

If this is happening to your machine, it is most likely due to a clogged drain. Washers have a catch for things like coins that may fall out of your clothes, and this catch prevents them from going down the drain and causing a more serious blockage.

When this catch becomes clogged, the washer frequently does not stop spinning because it is attempting to wait for the blockage to be cleared. Look in your owner’s manual for the location of your washer’s coin catch and clear any obstructions that may exist.

Alternative Video: How To Fix Whirlpool Washer That Won’t Enter Spin Cycle

RECOMMENDED POSTS:

• Lawn Mower Blowing White Smoke: 3 Effective Methods To Try See More
• View: How To Reset White-Rodgers Thermostat Effortlessly In Seconds?
• How To Fix Roku TV Keep Turning Off? (5 Easy Ways)

WHIRLPOOL WASHER NO HIGH-SPEED SPIN

If your Whirlpool washer starts the wash cycle but does not reach the high-speed spin you’re used to, the problem is most likely simple to resolve. After the rinse cycles, the washer most likely has too much water in it.

The machine will not engage in the high-speed spin if there is too much water in it. This excess of water is almost certainly the result of an uneven load in the machine.

The clothes could be clumped together and retaining a lot of water. Simply double-check that the load is evenly distributed before restarting the washer.

WHIRLPOOL WASHER STUCK ON SENSING

Another issue you may encounter with your Whirlpool washer is it becoming stuck in one stage of the cycle. If it becomes stuck on the sensing stage, the washer may not start. It will simply keep blinking the sensor light.

If your washer’s sensor light keeps blinking without doing anything, there could be something stuck in the inner and outer tubs. The sensor detects when the inner tub and spinning hub are aligned. Once the inner tub is in place, the sensor will signal the start of the rest of the cycle.

When your washing machine is stuck in sensing mode, the sensor is detecting a problem somewhere in the machine. Check around the outside of the inner tub for anything that might be preventing the inner tub from dropping into place, such as a stray sock or shirt.

WHIRLPOOL WASHER TURNS ON THEN OFF IMMEDIATELY

What happens when you turn on your washer and it immediately turns off? Is this a serious problem? If this is what your washer is doing, a variety of things could be happening.

The door latch is the simplest place to begin. If the following events occur, this could be a problem:

1. Close the washing machine door.
2. Turn on the washer.
3. The washer door is locked.
4. Washer sits for a brief moment—or perhaps moves a little.
5. The washer’s door is unlocked.
6. The washer is turned off again.

If this is the sequence of events, you most likely have a problem with the door lock. This is typically a simple fix, such as replacing a latch or installing a new lock. Also, unplug your washer for two minutes before plugging it back in and restarting the cycle.

WHIRLPOOL WASHER DOESN’T SPIN SOMETIMES

If your Whirlpool washer is intermittently spinning, there are two possible causes and a few more that are more difficult to resolve.

The first reason your washer may be spinning on and off is that you are opening the lid too frequently. If you open the washer lid and add a last-minute pair of jeans to be washed, you may be disappointed by the lack of spinning.

Most washers have a two-minute delay between when the lid is opened and when they begin spinning again. Simply being patient is the solution. A broken lid switch is the next possible cause of your washer’s erratic behavior.

The lid switch is powered, and when the lid is closed, the switch turns on and tells the washer to start. When the switch is broken, it can randomly turn on and off.

When this happens, the washer believes the lid is being opened and closed and will wait two minutes before turning back on. If this is the case, the switch will need to be replaced.

WHIRLPOOL WASHER STOPS AT SPIN CYCLE

Faulty switches are the most common cause of your Whirlpool washer stopping at the start or in the middle of a spin cycle. For your washer to work, two main switches must be turned on. They are similar but distinct.

LID SWITCH

The lid switch is a sensor that informs the machine when the lid is closed. If the machine believes the lid is open, it will not operate. Every top-load washer has a lid switch. A similar sensor may be found in the door of a front-load washer.

DOOR LOCK

The lid switch should not be confused with the door lock. When the washer is engaged, a door lock prevents it from opening. A washer may have a lid switch as well as a door lock. Door locks are almost always present in front load washers, but they can also be found in top load washers.

Your Whirlpool washing machines will stop washing if either of these switches fails. It’s entirely possible that your washing machine’s repeated failures are caused by the failure of one or both of these switches.

To troubleshoot the issue, check the power continuity of the switches. This will tell you if there is an electrical problem with the switches. If they are receiving continuous power, the problem with the switches could be mechanical. The connections between the door and the machine’s body may be cracked or broken and must be replaced.

WHIRLPOOL WASHER KEEPS SHUTTING OFF

Nothing is more frustrating than a recurring problem that you don’t know how to solve. If you don’t fix the problem, the frustration you feel every time your Whirlpool washer shuts down will only get worse.

Inconsistent water flow is one factor that may cause your washer to shut down. If your washer does not receive enough water, the cycle will be terminated. This could be due to an interruption in the machine’s flow caused by a drain blockage or a plumbing issue.

Another source of inconsistency in the machine’s water is a wide range of water temperature. If your machine is set to run a hot cycle but is only receiving cold water from your plumbing, it will shut down.

Washing machines have an internal temperature gauge and will not finish cycles if the water temperature is incorrect. This is done to keep your clothes in good condition. To correct this, turn on both the cold and hot water faucets leading into the washing machine.

Also, ensure that the hoses delivering the water are properly tightened. Next, inspect your hot water tank to ensure it is producing the hot water required by your washing machine to clean your laundry.

WHIRLPOOL WASHER SHUTS OFF MID-CYCLE

As we’ve seen, washing machines frequently shut down in the middle of a cleaning cycle. Aside from the reasons mentioned above, there are a few more causes of random machine shutdowns.

1. Power Supply Failure

If the power system that powers your washing machine has any blips or inconsistencies in power, your machine may shut down at random. This will cause the machine to stop its cycle entirely. The machine will most likely not restart on its own, and it may not even drain.

2. Overheating

Washing machines, like any other machine, can overheat. Whirlpool machines have a safety feature that detects the machine’s and the motor’s temperature. If either of these temperatures reaches unsafe levels, the machine will shut down immediately.

3. There Are Too Many Suds

Depending on the model of your Whirlpool washer, it may turn off if there are too many suds in the tub. It may then stop and wait for the suds to subside, or it may perform an additional rinse cycle to remove some of the suds. To avoid this, use a high energy specific detergent.

CONCLUSION

You might call the service line for the first year after purchasing your Whirlpool washing machine because of the one-year warranty, but after that first 365 days, you’re likely to be more hesitant to call. Getting your major appliances serviced can be expensive, and you may be tempted to fix them yourself.

You can use this article as a guide to determine which of these issues are safe to try to repair yourself and which should be left to the professionals.

Frequently Asked Questions